Hướng dẫn sử dụng điện thoại panasonic kx ts500mx
– Điện thoại để bàn Panasonic KX-TS 500 rất ổn định chính bởi yếu tố đơn giản đến tối thiểu. Nó vận hành một cách trơn tru và cực kỳ ít lỗi. Gần như bạn có thể tin rằng chẳng có lý do gì khiến nó có thể bị hỏng trừ khi bạn cố tình đập phá nó. Show Điện thoại Panasonic KX TS500 lã mẫu điện thoại để bàn có thiết kế nhỏ gọn thanh lịch, phím bấm mềm, chất lượng ầm thanh HD rất phù hợp để lắp đặt cho các văn phòng, nhà máy, khách sạn và các hộ gia đình. Điện thoại Panasonic KX TS 500 từ lâu đã luôn được khách hàng tin dùng nhờ chất lượng và độ bên vượt trội. Ngoài ra Điện thoai Panasonic KX TS500 còn được trang bị thêm nhiều phím chức năng, giúp cho việc đàm thoại được thuận tiện nhất. Một số phím chức năng tiện lợi của điện thoại Panasonic KX TS500Nút tăng giàm âm lượng handset, cho phép người dùng có thể tằng hoặc giảm âm lượng trong quá trình đàm thoại, làm soa cho phù hợp nhất với mình, giúp cho cuộc đàm thoại thoải mái nhất, tăng năng suất làm việc Nút quay lại số gần nhất, với việc trang bị phím chức năng này người dùng điện thoại Panasonic KX TS500 sẽ không cần quay lại số mình vừ gọi việc này giúp cho người dùng tiết kiệm rất nhiều thời gian cũng như thao tác trên điện thoại Nút Flash giúp cho việc chuyển cuộc gọi giữa các máy trong nội bộ một công ty được diễn ra dễ dàng, đồng thời nó cũng giúp cho người dùng có thể giữ cuộc gọi để làm việc khác cần thiết xử lý trước mà không cần kết thúc cuộc gọi. Nút Cơ của Điện thoại Panasonic KX TS500Ngoài bàn phím và các nút điều khiển bằng tín hiệu điện, điện thoại Panasonic KX-TS500 còn được trang bị thêm 2 nút điều khiển cơ ở bên canh sườn nhắm giúp tăng giảm âm lượng chuông cũng như chế độ quay số để phù hợp với từng loại tổng đài điện thoại Nút Tone / Pulse: Với nút này người dùng có thể chuyển chế độ quay số cho điện thoại Panasonic KX-TS500 từ chế độ quay số xung sang chế độ quay số đa tần và ngược lại, giúp cho chiếc điện thoại hoạt động tốt với các hệ thống tổng đài điện thoại khác nhau. Nút Ringer: Nút này giúp cho người dùng điều chỉnh âm lượng chuông của cuộc gọi đến cho phù hợp với môi trường làm việc của mình. Có ba mức là, mức high dùng cho những môi trường làm việc có nhiều tiếng ồn, mức Low dùng cho môi trường làm việc có ít tiếng ồn và mức Off dùng khi ta cần không gian làm việc yên tĩnh 1 Getting Started1-A Location of controls4 Things You Should Know1-B Settings4-A Wall Mounting4-B Troubleshooting2 A BC 3 DEF 1 5 JKL 6 MNO 4 GHI 8 TUV 9 W XYZ 7 PQRS 0 T ONE FLASH REDIAL VOLUME ($) (TONE) Button (3-B) (FLASH) Button (3-A) RINGER Selector (1-B) (REDIAL) Button (2-A) DIALING MODE Selector (1-B) VOLUME (^), (_) Buttons (2-A) 1 Connect the telephone line cord (1). 2 Connect the handset cord (2), then confirm the dial tone. To Single-Line Telephone Jack Handset Cord Handset Telephone Line Cord RINGER Selector DIALING MODE Selector 1 2 1 When the unit rings, lift the handset.2 When finished talking, hang up.3 Set the DIALING MODE selector to TONE.≥If you cannot dial, set to PULSE. 4 Set the RINGER selector to HIGH, LOW orOFF. (Ex. “LOW” is selected.) 2-A Making Calls2-B Answering Calls1 Lift the handset. 2 Dial a phone number.≥If you misdial, hang up and start again from step 1. 3 When finished talking, hang up.To redial the last number dialedLift the handset. ➡ Press (REDIAL).To adjust the receiver volume (6 levels)while talkingTo increase, press (^).To decrease, press (_). ≥ After hanging up, the volume level will be saved. 2 Operation 3 Special Features3-A For Call Waiting Service UsersPress (FLASH) if you hear a call-waiting tonewhile talking. ≥The first call is put on hold and you can answer the second call. ≥To return to the first caller, press (FLASH) again. 3-B Temporary Tone Dialing(For Rotary or Pulse Service Users)Press ($) (TONE) before entering accessnumbers which require tone dialing. ≥The dialing mode changes to tone. You can enter numbers to access answering services, electronic banking services, etc. When you hang up, the mode will return to pulse. ≥Access numbers entered after pressing ($) (TONE) will not be included when redialing. To temporarily set thehandset down duringa conversation, placeit as shown here.The unit can be mounted on a wall. 1 Press the tabs in the direction of the arrows(1), then remove the wall mounting adaptor(2). To Single-Line Telephone Jack Screws 8.3 cm Hooks Problem The unit does not work. The call cannot be connected even if you dialed correctly. The unit does not ring. Remedy ≥Check the settings (1-B). ≥Check whether the DIALING MODE selector setting is correct or not (1-B). ≥The RINGER selector is set to OFF. Set to HIGH or LOW (1-B). 8.3 cmWall Template Take special care to follow the safety suggestions listed below. InstallationsEnvironment
near a bathtub, washbowl, sink, etc. Damp basements should also be avoided.
such as radiators, kitchen range, etc. It also should not be placed in rooms where the temperature is less than 5oC or greater than 40oC. Placement
onto, and liquids are not spilled into, the unit. Do not subject this unit to excessive smoke, dust, mechanical vibration or shock.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE. PQQX13679XA F0403-2073 DManufactured by Panasonic Communications (Malaysia) Sdn. Bhd. Senai Malaysia If trouble occurs, disconnect the unit from the telephone line and connect to a known working phone. If the known working phone operates properly, do not reconnect the unit until the trouble has been repaired. If the known working phone does not operate properly, consult your telephone company. For your future referenceSerial No. (found on the bottom of the unit) Date of purchaseName and address of dealer Integrated Telephone SystemOperating InstructionsModel No. KX-TS500MXPulse-or-tone dialing capability PLEASE READ BEFORE USE AND SAVE.∑ Handset. . . . . . . one ∑ Handset Cord. . . one ∑ Telephone Line Cord . . . . . . . . . . . . . one Accessories (included) 4-C Safety Instructions≥When set to OFF, the unit will not ring. 3 Install screws using the wall templatebelow. Connect the telephone line cord.Mount the unit, then slide down. ≥Fasten the cord to prevent it from being disconnected. 2 Tuck the telephone line cord inside the wallmounting adaptor, and push it in the direction of the arrow (1 and 2). ≥The word “UP WALL” should face upward. KX-TS500MXW 4-D SpecificationsPower Source: From telephone line Dimensions (H x W x D): Approx. 96 mm x 150 mm x 200 mm Mass (Weight): Approx. 475 g Dialing Mode: Tone (DTMF)/Pulse Operating Environment: 5°C–40°C Specifications are subject to change without notice. PQQX13679XA 03.7.1 5:38 PM ページ 1 |